If Windows will not load from an SSD, the fastest fix is to work out which of three situations you are in: the drive is not detected at all (check the cable, M.2 seating and BIOS), the drive is detected but Windows cannot boot from it (check boot mode, boot order and the boot files), or the Windows installer cannot see it (load the storage driver or change the storage mode). Start by confirming the drive shows in the BIOS or UEFI setup screen, because that single check splits the problem in two.
As an Amazon Associate we earn from qualifying purchases at no extra cost to you.
Our Top Picks
Top 3 picks at a glance
Step 1: Is the SSD visible in the BIOS?
Enter the firmware setup screen at startup; the key is usually shown on the first screen or listed in the motherboard manual, and varies by maker. Look for a storage or boot section that lists connected drives. Menu names differ between boards, so consult the manual for yours.
- Listed: The hardware link is working. Go to the boot settings sections below.
- Not listed: Power off, unplug the PC from the wall, then reseat the drive. For an M.2 drive, remove the screw, check that it sits fully in the slot and is held down. For a SATA SSD, reseat both the data cable and the power connector, or try another port. Do this only with the power cable removed, and discharge static by touching bare metal on the case.
Also check the motherboard manual for slot behaviour. M.2 slots can support NVMe, SATA or both, and some boards disable certain SATA ports when an M.2 slot is populated. Reference material on the M.2 standard notes that a module can connect over PCIe or SATA, which is why a drive that fits physically may not work in a slot wired for the other interface.
Symptom, cause and fix table
| Symptom | Common cause | First fix to try |
|---|---|---|
| Drive missing in BIOS | Loose M.2 or SATA cable, wrong slot type | Reseat, try another slot or port, read manual |
| Drive in BIOS, “no bootable device” | Boot order, missing boot files, wrong boot mode | Set the drive as first boot device; check UEFI versus legacy mode |
| Installer shows no drives | Missing storage driver or RAID/VMD mode | Load the driver from the maker, or change the storage mode |
| Installer refuses the disk | Partition style does not match boot mode | Match GPT to UEFI, or MBR to legacy; or clean the disk |
| Windows starts, then blue screen | Driver issue after cloning or mode switch | Revert storage mode; run startup repair |
| Drive visible in Windows but not in File Explorer | No drive letter or not initialised | Open Disk Management; assign a letter or initialise |
| Drive vanishes intermittently | Overheating, power saving, failing drive | Check temperature, firmware updates, back up data |
Step 2: Check boot mode and boot order
Modern Windows 11 installs use UEFI with a GPT-partitioned disk. If the SSD was prepared in a different mode, for example cloned from an older legacy-BIOS drive, the firmware may not find a boot loader. In the firmware setup, confirm that the SSD (often shown by its model name or as Windows Boot Manager) is first in the boot order. If you cloned from another drive and removed it, make sure the clone included the EFI system partition.
Switching between UEFI and legacy (CSM) mode without converting the disk can stop Windows loading. Changes in the BIOS can cause instability or affect warranty, so change one setting at a time and note the original value so you can return to it.
Step 3: Windows Setup cannot see the drive
When you reach the “where do you want to install Windows” screen and the list is empty, the installer lacks a driver for the controller. Common situations are NVMe drives on systems using Intel Rapid Storage Technology with VMD enabled, or AMD RAID mode. The motherboard or PC maker’s support page lists the correct storage driver for your model.
- On another PC, download the driver package from the motherboard or PC maker’s support page for your exact model.
- Extract it to a USB drive.
- In Windows Setup choose the option to load a driver, browse to the USB drive and select the driver.
- The SSD should now appear. Continue the installation.
An alternative is switching the storage mode in firmware to a standard AHCI or NVMe mode where your manual says that is supported. Switching modes on a system that already has Windows installed can prevent it from booting, so do it before installing or follow the maker’s guidance.
Step 4: Disk is detected but cannot be used
If the installer says Windows cannot be installed to the disk because of its partition style, the boot mode and the disk’s partition scheme do not match. Either change the boot mode to match the disk, or wipe the disk and let the installer recreate partitions. Wiping a disk erases everything on it, so copy needed data elsewhere first.
If Windows is already running but the SSD does not appear in File Explorer, open Disk Management. A new drive often needs to be initialised, then given a volume and drive letter. A drive marked offline can usually be brought online from the same tool.
Step 5: Repair an existing installation that stopped loading
Boot from a Windows installation USB, choose Repair your computer, then Startup Repair. This can fix a damaged boot configuration. If that fails, the recovery command prompt provides tools to inspect partitions and rebuild boot files; follow Microsoft’s documentation for the exact commands for your Windows version rather than copying from random forum posts. If the drive was working until a power loss or failed update, back up your data from the recovery environment if possible before more drastic repair.
Step 6: Update firmware and check health
SSD makers provide utilities for checking drive health and updating firmware. Some drives have had firmware that fixes disappearing-drive bugs. Check the maker’s support page for your exact model, and back up data before a firmware update. Also update the motherboard BIOS if the manual or maker’s release notes mention storage compatibility fixes, but only follow the maker’s instructions precisely, because an interrupted BIOS update can render the board unusable.
A drive that frequently disappears, shows very slow speeds or reports errors may be failing. Contact the maker for warranty service and avoid writing more data to it.
Common mistakes
- Changing several BIOS settings at once, so you cannot tell what worked.
- Installing Windows on a disk while another drive with an older boot loader remains connected, which can place the boot files on the wrong drive. Disconnecting other drives during installation avoids this.
- Forgetting that an NVMe drive needs an M.2 slot wired for PCIe.
- Assuming a new SSD appears automatically; many need initialising first.
- Cloning without checking boot mode afterwards.
- Not backing up before using repair commands.
When to get help
If the drive does not appear on a second PC or in a USB enclosure either, the drive itself is likely faulty and the maker’s warranty route is the next step. If it appears elsewhere but not in your PC, the problem is probably the slot, cable, BIOS or motherboard, and a technician or the motherboard maker’s support can help. Never open a power supply to investigate; if you suspect a power fault, ask a qualified technician.
Frequently Asked Questions
Why does my new SSD not show up in Windows?
The most common reason is that it has not been initialised or given a drive letter, which you can do in Disk Management. If it does not appear there either, check the BIOS to see whether the drive is detected at all.
Why does Windows Setup show no drives for my NVMe SSD?
The installer may lack the storage driver for the controller, often when RAID or VMD mode is enabled. Download the driver from the PC or motherboard maker for your exact model and load it from a USB drive during setup.
What does “no bootable device” mean?
The firmware cannot find a usable boot loader on the selected disk. Check the boot order, confirm the boot mode matches the disk’s partition style, and run Startup Repair from installation media.
Can a cloned SSD fail to boot?
Yes. If the clone lacks the EFI system partition or the boot mode differs from the original, Windows will not start. Check the boot mode first, then use Startup Repair.
Could my SSD be dead?
Possibly, if it is missing in the BIOS, in another PC and in an enclosure. Back up anything you can reach and contact the maker about warranty.
Related guides
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeA Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.
See Prime for Young AdultsAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAs an Amazon Associate we earn from qualifying purchases.


![ASUS Transformer Book - Intel Atom - 2GB Memory 500GB [Keyboard Dock] HDD 32GB SSD - 10.1" Touchscreen Tablet - Windows 8.1](https://m.media-amazon.com/images/I/41MXXXlexjL._SL160_.jpg)
