When a secondary monitor flickers, the quickest things to try are a different cable, a different port, and setting both screens to the same refresh rate in Windows display settings. Most flicker on a second display comes from the cable, the refresh-rate configuration or the graphics driver, and rarely from the panel itself.
As an Amazon Associate we earn from qualifying purchases at no extra cost to you.
Our Top Picks
Top 3 picks at a glance
Symptom, Cause and Fix Table
| Symptom | Common cause | First fix |
|---|---|---|
| Whole second screen blinks or goes black briefly | Loose or damaged cable, or poor adapter | Reseat or replace the cable |
| Flicker only when the second screen is connected | Mixed refresh rates between displays | Match refresh rates, or try lowering the faster one |
| Flicker with video or a browser on the second screen | Hardware acceleration or driver behavior | Turn off hardware acceleration in the app; update driver |
| Flicker after a driver update | New driver bug | Clean install or roll back the driver |
| Flicker at certain brightness levels | Monitor backlight dimming (PWM) behavior | Raise brightness; check the maker’s settings |
| Flicker with adaptive sync on | VRR range or cable limit | Disable adaptive sync on that screen to compare |
| Flicker on every PC and cable | Monitor fault | Contact the maker for repair or warranty |
Step 1: Reseat and Swap the Cable
Power the monitor off and reseat the cable at both ends. If it still flickers, replace the cable with a different one of the same type. A cable that carries the signal at 60 Hz can fail at higher refresh rates or resolutions, so a cable rated for the mode you are using is important. Examine connectors for bent pins or damage. If you see any, stop and contact the maker or a technician.
Adapters and docks add another point of failure. If the second monitor connects through an adapter, try a direct connection to the graphics card to find out whether the adapter is the cause.
Step 2: Try a Different Port
Use another output on the graphics card, such as switching between HDMI and DisplayPort. Always connect monitors to the graphics card rather than the motherboard when a dedicated card is installed. Some graphics cards handle multiple monitors better on certain ports, and the card maker’s manual or support pages list limitations.
Step 3: Match the Refresh Rates
A common cause of flicker in multi-monitor setups is a mismatch in refresh rates or resolutions between the screens, which forces the graphics card and Windows to juggle different timings. Set both displays to compatible settings:
- Right-click the desktop and open Display settings.
- Select the flickering monitor, then open Advanced display.
- Choose a refresh rate in the drop-down, ideally the same as, or a clean fit with, the main monitor.
- Repeat for the main monitor and watch whether the flicker stops.
Some users report that a high-refresh primary monitor combined with a lower-refresh secondary monitor can cause idle clock behavior on the GPU that shows up as flicker. If you see this, test a matching rate. Behavior differs by graphics card and driver generation, so treat this as a test, not a guaranteed fix.
Step 4: Update or Roll Back the Graphics Driver
Download the current driver from the graphics maker’s support page, install it, and restart. If the flicker began just after an update, the maker’s installer often offers a clean installation option, and Windows lets you roll back a driver in Device Manager. Also run Windows Update, since display fixes sometimes arrive there.
Step 5: Check Hardware Acceleration and Apps
If the flicker appears only in a browser, a video player or a chat app, the cause may be hardware acceleration. Turn off hardware acceleration inside that app’s settings and test. Overlays, screen recorders and customization tools can also interfere with how windows are drawn, so close them one at a time.
Step 6: Review Adaptive Sync and HDR
Variable refresh rate and HDR can both introduce flicker when the screen’s range or the cable’s bandwidth is stretched. Temporarily switch off adaptive sync or HDR for the secondary monitor in Windows and in the graphics control panel, then see if the problem goes away. If it does, check the monitor maker’s supported range and consider a higher capability cable. Menu names differ by maker.
Step 7: Look at Power and the Monitor Itself
- Plug the monitor directly into a wall outlet instead of a crowded power strip, and keep it away from large electrical devices.
- Use the on-screen menu to reset the monitor to factory defaults, which clears odd settings like overdrive.
- Lower overdrive or response-time options, if the monitor offers them, since aggressive settings can produce visual artifacts.
- Update monitor firmware only if the maker publishes a process and instructions.
Do not open the monitor or its power adapter. Internal components can hold dangerous charge, so leave repair to the maker or a qualified technician.
Backlight Flicker vs Signal Flicker
These are different problems. Backlight flicker is built into how a monitor dims. Wikipedia notes that LED designs can use pulse-width modulation at rates from several kilohertz down to 180 Hz, which can be perceptible to some people, and that flicker-free dimming exists in other designs. If you feel eye strain or headaches at certain brightness levels, check the maker’s spec for flicker-free features, and speak to a doctor if the discomfort continues.
Signal flicker, which this guide mainly addresses, shows up as blinking, black frames or horizontal bars due to cable, timing or driver trouble. It generally changes when you swap cables or settings, whereas backlight flicker follows the brightness setting.
Decision Table: What to Change First
| If you notice… | Try this first |
|---|---|
| Blinking that follows touching or moving the cable | Replace the cable and reseat connectors |
| Flicker only when two monitors have different refresh rates | Match refresh rates |
| Flicker only in one program | Disable hardware acceleration in that program |
| Flicker started after a driver or Windows update | Roll back or clean-install the driver |
| Flicker changes with brightness | Adjust brightness and check the monitor’s flicker-free spec |
Common Mistakes
- Replacing the monitor before testing a different cable and port.
- Using the motherboard output while a graphics card is installed.
- Running a long, cheap or uncertified cable at a high refresh rate.
- Installing a driver on top of a faulty one without cleaning it.
- Leaving adaptive sync on without checking the monitor’s supported range.
- Opening the monitor housing, which is unsafe and can void the warranty.
When to Contact the Maker
If the second monitor flickers on another PC, with a different cable and at default settings, the unit probably has a hardware fault. Contact the manufacturer and have the model, serial number and purchase details ready. If the flicker follows your PC with several monitors, the graphics card, a driver or the PC power supply could be the cause, and a technician can help narrow it down.
Frequently Asked Questions
Why does only my second monitor flicker?
It often uses a different cable, port or refresh rate than the main screen. Swapping the cable and matching refresh rates are the best first tests.
Can different refresh rates cause flicker?
Yes. Users report that mixing refresh rates across monitors can produce flicker, depending on graphics card and driver. Setting compatible rates is a simple way to test whether that applies to you.
Could my graphics driver be the cause?
It could. A new driver may introduce a bug, and a corrupted one can behave oddly with multi-monitor setups. A clean install or rollback is a standard step.
Is flicker bad for my eyes?
Visible flicker can cause discomfort or eye strain for some people. If you have headaches or vision symptoms, take breaks, fix the flicker and consult a doctor or optician.
Should I turn off adaptive sync on the second monitor?
Turning it off is a useful test. If the flicker stops, the issue is likely the supported range, the cable or the driver, and you can decide whether to keep adaptive sync on the main screen only.
Related guides
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeA Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.
See Prime for Young AdultsAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAs an Amazon Associate we earn from qualifying purchases.


